Fittings

POLE CLAMPS

  Manufacture diameters: 3” to 4” 4” to 5” 5” to 6” 6” to 7” 7” to 8” 8” to 9” General tolerance: +-1mm. Electrical networking: plates are manufactured of 1” × ½” × ¼” Telephone networking: plates are manufactured of 1” × ½” × 3/16”. Are manufacture of 1 outlet, 2 outlets or without outlet, to specify 4” to 5”, it mean that 4” is the minimum dimension which the clamp working fine. DESCRIPTION. The pole clamp[...] See more
 POLE CLAMPS

ROUND WASHER

  DESCRIPTION Washers avoid loosening or loss of tension between the parts assembled. Washer is manufactured of carbon steel, it must be cold, after formed should be subjected to quenching and tempering treatment. Galvanization of this piece is done hot according to standard ICONTEC 2076. Washers are properly treated after coating to avoid the attenuation for hydrogen. The washer is placed between the jaws of a vise and is press up to compress completely. The[...] See more
 ROUND  WASHER

ANCHORAGE BAR

Manufacture in IU + 2205 of ½”, 5/8”, ¾” and a length of 1.5 - 1.8 and 2.4 mts DESCRIPTION The anchor rod is used to set the reins of the pole to the ground, in combination with the anchor block or died disk to rein determined. The cross and support foot are used to support airs network carriers. Rods, cross and support foot are manufactured in steel, hot galvanized, meeting the technical and functional specifications required by national and international[...] See more
 ANCHORAGE BAR

spacer

Manufacture in: Bar Ø 3/8”, ½” and 5/8” and lengths from 1-1/2” to 14”, the angles measure are before[...] See more
 spacer

SCREW MACHINE

DESCRIPTION Bolts, screws and spacers are ironworks that are used as fasteners, assembly and coupled with other hardware of the telephone network of outside plant, both aerial like channeled. Are manufactured in steel with low content of carbon, hot galvanized, high corrosion resistance, meeting the technical and functional specifications required by national and international standards. Manufacture in: Bar Ø 3/8”, ½” and 5/8” and lengths from 1-1/2” to[...] See more
 SCREW MACHINE

STAPLE

Material: Steel sheet AISI 1020 Steel screw AISI 1010 Steel nut ASTM A-307 Galvanized in a hot according to the standars ASTM 2076 A 153. Dimensions: 3/8”(1-1/2” and 2”) DESCRIPTION Are used to lie steel cables in winds from caliber 6.35 mm (1/4“) to caliber 9.5[...] See more
 STAPLE

EYE NUT

Material: Steel foundry quality SAE 1030 Coating: Galvanized for hot immersion and shall comply with the specifications given in Sta3/8”, ½” and 5/8”ndard NTC 2076. Function: eye nut is used to set type suspension insulators to cross, etc. Dimensions: 3/8”, ½” and 5/8”. DESCRIPTION Eye Nut is used to set type suspensión insulators to cross or the[...] See more
 EYE NUT

STAINLESS STEEL CLOSURES

  DESCRIPTION The closure or buckle that is used to fasten the ribbon of stainless steel, Comprises a body with wings and a line of slot that allows the mooring of the tape. The closure comes in stainless steel sheet of high mechanical strength Simelca manufacture ribbon and closures in stainless steel of 3/8, ½”, 5/8” and[...] See more
 STAINLESS STEEL CLOSURES

STAINLESS STEEL RIBBON

STAINLESS STEEL RIBBON . A roll/ feet specifictions of the strip. ½” 100 Cal:2210.760 mm ¾” 100 Cal:2210.760 mm 3/8” 100 Cal:2410.607 mm 5/8" 100 Cal:2210.767 mm DESCRIPTION The stainless steel ribbon is used as a lanyard for some ironwork or accessories to the parts of the telephone network placed on the poles. The ribbon is manufactured in stainless steel type AISI 201 and 304 of high mechanical resistance that meets the technical requirements and[...] See more
 STAINLESS STEEL RIBBON

CROSS PIECE

  Description: The crosspieces are used to support the conductors in aerial nets. The crosspieces are fabricated in steel, hot galvanized, accomplishing the specific technical and functional norms, required nationally and internationally. They are fabricated mainly: Crosspieces of 1.2, 1.5, 2.0, 3.6 and 4.5[...] See more
 CROSS PIECE

DOW BRACKET

  DESCRIPTION: The pieamigos are used to support drivers in overhead networks. They are made of steel, hot dip galvanized, complying with the functional and technical specifications required in national and international standards. They MANUFACTURED MAINLY: Pieamigos 1.2, 1.5, 2.4 and 3.6[...] See more
 DOW BRACKET

SUPPORT OF 13.2 AND 44 KV COMPACT CABLE

DESCRIPTION: Reference support wire 13.2 kV compact extragalvanizado hot air to support compact networks in electrical[...] See more
 SUPPORT OF 13.2 AND 44 KV COMPACT CABLE

L SUPPORT CIRCUIT BREAKER AND LIGHTING CONDUCTOR, 13.2KV AND 44 KV

DESCRIPTION: Support a cut in air circuits compact networks in electrical[...] See more
 L SUPPORT CIRCUIT BREAKER AND LIGHTING CONDUCTOR, 13.2KV AND 44 KV

HORIZONTAL SUPPORT REF 280mm AND 450mm

Horizontal support extragalvanizado hot to handle cables in the installation of[...] See more
 HORIZONTAL SUPPORT  REF 280mm AND 450mm

SUPPORT FOR TRANSFORMER

Support for transformer transformer separates the front of the house or places where there is a risk of contact. COATING: hot dip[...] See more
 SUPPORT FOR TRANSFORMER

VERTICAL SUPPORT, DIAMETER 5/8” REF 500mm AND 1000mm

Vertical support extra hot galvanized for supporting cables in cameras[...] See more
 VERTICAL SUPPORT, DIAMETER 5/8” REF 500mm AND 1000mm

3 TONS TENSOR

Hardware used to tensioning the messenger or wind cable that re located in[...] See more
 3 TONS TENSOR

EYE BOLT TENSOR 3/8”

Used to guide the wire (neoprene) for house[...] See more
 EYE BOLT TENSOR 3/8”

ANCHOR BOLT TAIL

Pin used in the telecommunications inspection cameras for fixing the vertical supports to the[...] See more
 ANCHOR BOLT TAIL

STAPLE 100 TO 2400 PS

They are good to fix telephonic cables in the horizontal supports that are located inside the inspection[...] See more
 STAPLE 100 TO 2400 PS

Plastic Clamp

Elements placed in the messenger cable for fixing the telephonic cables of optic[...] See more
 Plastic Clamp

Hanging Eriband Tipe Clamp

Hardware fabricated in nodular Steel that is use dot fix messenger cables in step[...] See more
 Hanging Eriband Tipe Clamp

Messengers Terminals

Hardware fabricated in nodular Steel that is used to fix Messenger cables in the step[...] See more
 Messengers Terminals

RINGS OF RETENTION, SUSPENSION, AND DISTRIBUTION

Distribution ring: ring used for hook the plastic tensors. They are installed in the posts with stainless steel tape. Tensor ring: allows tensioning the neoprene cable when arrives to the façade of the house. Eriban suspension ring: allows guiding the cable through the post. It is fixed with stainless steel tape. Wall guide ring(35mm): it is installed in the facades of the house to guide the neoprene wire until the block of a[...] See more
 RINGS OF RETENTION, SUSPENSION, AND DISTRIBUTION